ALESIS STUDIO REFERENCE AMPLIFIER RA 150

Allen & Heath Zone 62 Club Mixer Technical Specifications 0dBu = 0.775 Volts rms +4dBu = 1.23V rms 0dBV = 1 Volt rms -10dBV = 316mV rms Maximum output level XLR +26dBu into >2k ohm load TRS jack +21dBu into >2k ohm load RCA Phono +15dBu into >10K ohm load Internal headroom Channels +21dB Mix to output +23dB Peak indicators Turn on 5dB before clipping Meters MIX /MONITOR Peak hold 12 LED 3 colour STEREO CHANNEL Peak reading 4 LED 3 colour Frequency response 20Hz to 40kHz +0/-1dB Distortion THD+noise measured at +14dBu 1kHz < 0.006% Crosstalk channel shutoff measured at 1kHz < 90dB Noise measured rms 22Hz to 22kHz MIC EIN -128dB referred to 150 ohm source Residual output noise XLR -90dBu (-94dB S/N) TRS jack -84dBu (-84dB S/N) L RCA -92dBu (-84dB S/N) Mix noise, ch routed XLR -86dBu (-90dB S/N) TRS jack -82dBu (-82dB S/N) RCA Phono -91dBu (-83dB S/N) Power Supply Internal switch mode power unit with auto sensing mains input. MAINS IN socket IEC 3 pin Power lead Country dependent with moulded mains plug supplied AC mains 100 to 240V AC @ 50/60Hz Consumption 30W max Mains fuse rating 100-240V AC T500mA 20mm

Processor-Controlled 400-Watt 2-Way PA Speaker System with 12" Woofer and 1.25" Titanium Compression Driver

The state-of-the-art EUROLIVE B412DSP PA speaker system boasts 600 Watts that will simply blow you away. It holds a bi-amped 600-Watt engine which drives a high-efficiency 12" woofer for brutal punch and a 1.75" titanium driver for high-end resolution. The built-in mixer allows you to run the show without any extra equipment. But this animal also has a brain: a powerful 24-bit DSP controls the crossover, a dual compressor/limiter, phase and time corrections and even a noise gate. The intelligent dynamic EQ makes sure your system sounds perfect at any sound level. Best of all, you don?t have to be a gorilla to carry it.

High-performance 1600-Watt subwoofer for PA applications
Extremely powerful 18' long-excursion driver provides incredibly deep bass and acoustic power
Extremely high sound pressure level (100 dB half space 1 W @ 1 m)
40 Hz - 300 Hz frequency range (-10 dB), impedance 8 Ohms
Precise reproduction of ultra-low frequencies with a clear, powerful punch
Switchable crossover for optional passive or bi-amping operation mode
Pole socket for mounting with commercial spacer poles
Ergonomically shaped handles for easy transport
Rugged steel grill for optimal speaker protection
Professional speaker connectors, compatible to Neutrik® Speakon®
High-quality components and exceptionally rugged construction ensure long life

2 Oscillator + Noise Generator,
Multi Mode Filter (-24dB/oct LPF, -12dB/oct LPF/BPF/HPF),
EG x2,
LFO x2,
Virtual Patch x4
Vocoder Program: Voices = 4 voices

MIDI sliders
12 MIDI knobs
10 MIDI buttons
MIDI crossfader
DJ mixer-inspired layout
Powered via USB
Class-compliant with Windows XP* and Mac OS X
On/off switch

Line: 6.5V rms max
Headphone: 0.5W into 47 ohm
Distortion: less than 0.01%
Bass: +6/-32dB @40Hz
Middle: +6/-32dB @1.35KHz
Treble: +6/-32dB @15KH
Channel Kill: 80dB at 20Hz-20KHz

Quick Return
Enables a track to return instantly again and again to a cue point just by pressing the surface of the Jog Wheel.
Auto Beat Loop
Uses 4 timing buttons to instantly create perfect 1, 2, 4, or 8 beat loops. When a loop has been produced manually with the loop in and loop out buttons, this feature allows instant 1/1, 1/2, 1/4/, 1/8 beat cuts of the initial loop.

Features:
Hot Cue (sampler)


Memorizes up to 3 cue point?s per CD. These points can then be recalled by hitting either of the A, B or C buttons. This function can also be used like a mini sampler for vocals, stabs, or breaks, adding that touch of creativity to any DJ set.

Reverse

Instant reverse is controlled by using a flickable switch. With no loss of tempo or pitch, it can be used immediately within any track without having to stop or start. Reverse can also be used with the Hot Cue and the Loop Sampler providing endless combinations and effects.

Real Time Seamless Loop

A quick and simple way to set a loop while a track is playing. Once the loop is set, it can then be looped continuously or until the ReLoop / Exit button is pressed. When released, the track continues playing without any pause. The loop can be re-trigged at any time by hitting the ReLoop button

Loop In / Out Adjust

Another world first from Pioneer - is the ability to adjust both the In and Out points of a loop stored in memory. So now fine tuning a loop is both quick and easy. Loop-In adjust is only available on the CDJ-1000.

Reloop

Hitting the Reloop button instantly takes you back to the beginning of the loop stored in the CDJ-1000?s memory. This can be done either while the loop is playing or at any time while the current track is playing. Clever use of Reloop can create some sample like effects. The same loop is always stored in memory until replaced with a new loop.

Memory
MMC - MultiMediaCard

The CDJ-1000 has a memory feature that let?s you store Wave Data as well as Cue and Loop points. The data can be stored on a removable memory card (MMC) or the players internal memory. The removable MMC card can also be used in any CDJ-1000, so once you?ve stored your favorite cue and loop points they?re there for life. The CDJ-1000 also has a feature that allows you to duplicate MMC cards. (Multimedia Card (MMC) is not supplied with the CDJ-1000.)

Wave Data

CD Wave data is always saved on to the MMC when inserted and then appears instantly.

Cue / Loop Memory

Once you set a cue or loop point you can save it to either the internal memory or MMC card by hitting this button.

Delete

Gets rid of those Cue or Loop points that you shouldn?t have bothered saving in the first place.

Call

A quick and easy way to scroll through saved cue and loop points.

CD Control
CD Control Buttons

High Quality Aluminium buttons ? Track Search, Search, Cue and Play / Pause
Pitch Bend

Is used to either speed up or slow down the tempo of the music depending the direction the jog dial is rotated ? either forward or reverse

Jog Mode

The CDJ-1000 can be set in either Vinyl or CDJ mode. In CDJ mode, the jog dial functions just like a Pioneer CDJ player, but without the touch sensitivity.

Scratch Play / Cue

When the CDJ-1000 is in vinyl mode, the top of the jog dial functions just like a Vinyl Turntable. Pressing down stops the music and allows you to scratch or cue your track by rotating the jog dial in either direction.

Vinyl Speed Adjust Touch/Brake

This allows adjustment in the speed at which the CD slows down until it stops.

Vinyl Speed Adjust Release/Start

This allows adjustment of the speed at which the CD returns to normal playback speed.

Tempo
Master Tempo

Pioneer?s Master Tempo locks the pitch of the track even when you change the speed. You can speed up or slow down the beat without any noticeable difference in how the vocal and instruments sound.

Tempo Control

A new 100mm linear high precision slider connected to a 0.02% (at +/- 6%) adjustment indication on the display panel. Giv es the DJ?s that total control and ensures that the tempo adjustment is easy and accurate.

Tempo Control Range

Ranges of +/- 6%, +/-10%, +/-16% and +/-24% can be assigned to the Tempo Control slider to offer a greater range of adjustment than on any of the pr evious Pioneer CDJ?s.

Tempo Control Reset

Resets the tempo to 0% or original tempo of the track regardless of the slider position. The button has been recessed to prevent accidental selection.

Eject Button & CD Lock

The CDJ-1000 does have a guard to prevent you from accidentally pressing it the eject button. The CD is locked until the track is stopped. This can be deactivated as well if you are looking to do quick mixes.

Multi-Read Format

The CDJ-1000 can read CD, CD-R and CD-RW disks.

Front Loading

Loading CD?s without having to open doors or trays makes swapping discs and selecting tracks that much faster. It also helps to keep dirt and any nasty substances out of the CD?s working parts.

Cue Functions
Auto Cue

This is the fastest way to find the beginning of a track. The sound level can also be changed to suit your style of music (-36db to ?78db). There is also an option to turn it off if you prefer to cue up your CD tracks manually.

Manual Cue

Cue points can be set anywhere on the CD using either the Vinyl or CDJ mode. Adjustment is made by using either the jog dial or manual search buttons. The cue point is automatically stored in the internal memory (If MMC is inserted in CDJ-1000, the cue point is automatically stored in the MMC.) until it is overwritten with a new cue point. (Jog resolution for both Vinyl and CDJ modes - 135 frames per revolution / 75 frames = 1 second)

Real Time Cue

A cue point can be set on the fly and stored into the internal memory by just simply hitting the In / Real-time cue button.

Pioneer Offers More!

Fader Start / Back Cue Start When the CDJ-1000 is used with the DJM-600, DJM-500, DJM-300 or DJM-300S mixer, you can start the music by sliding the cross fader. By sliding the fader back, it will return the CDJ-1000 back to the previously selected cue point.

Built For The Professional DJ

To prevent accidental CD ejection or loss of mains power, the CDJ-1000 has safety guards around the power and eject buttons together with a locking feature.

Relay Play

Connecting two CDJ-1000?s with a standard 3.5mm mini-plug cable allows one unit to be put on standby whilst the other plays. Relay Play automatically starts the second player enabling them to play 'back to back' to give you endless music play.

Legato Link Conversion For High Quality Sound

Equipped with Pioneer?s wide r ange technology? Legato Link Conversion. The CDJ-1000 is capable of reproducing sound frequencies above 20kHz, which are lost during normal CD-format playback. Not only does this give great sound reproduction but sounds closer to the original recording and more analog like vinyl.

Shock-Proof Memory and Anti-Vibration Construction

Sound jumps or skipping is prevented by using a 16 second shock-proof memory for normal CD play (minimum of 10 seconds if scratching and reading wave data at the same time in Vinyl mode).

Anti-Vibration

Oil-dampened floating suspension prevents sound skipping, even when the player is subjected to impact during use or vibrations generated from high volume music and low frequency bass.

Digital Output

The CDJ-1000 is equipped with a switchable on/off
digital output (phono) which can be utilized for studio use.

CD / Line ?14dBV (200mV) / 22kW
Phono ?54dBV (2mV) / 47kW
Main Mic ?54dBV (2mV) / 3kW
Sub Mic ?60dBV (1mV) / 3kW
Return ?14dBV (200mV) / 22kW Output Terminals
Master Out1 (RCA) 0dBV (1V) / 1kW
Master Out2 (XLR) 4dBm (1.23V) / 600W
Rec Out (RCA) ?10dBV (1V) / 1kW
Booth Monitor 0dBV (1V) /1kW
Send ?14dBV (1V) / 1kW
Phones 0dBV (1V) / 22W Frequency Characteristics
CD / Line / Phono 20Hz to 20kHz Signal To Noise Ratio
CD / Line 87dB (with effects off)
Phono 77dB
Mic 69dB Total Harmonic Distortion Rate
CD / Line / Phono Below 0.02%
Cross Talk Over 70db Channel Equalizer
Hi +12dB, ?26dB (13kHz)
Mid +12dB, ?26dB (1kHz)
Low +12dB, ?26dB (70Hz) Microphone Equalizer
Hi +12dB, ?12dB (10kHz)
Mid +12dB, ?12dB (1kHz)
Low +12dB, ?12dB (100Hz) Effector
Delay and Echo 1 to 3500mSec
Pan, Trans, Filter & Flanger 10 to 16000mSec
Reverb 1 to 100%
Pitch 0 to ±100% Miscellaneous
Power Requirements: AC 120V, 60 Hz
Power Consumption: 36 W
Net Weight: 14 lbs 9 oz (6.6 kg)
Dimensions (WxHxD): 320x107x357.4 mm (12-3/8 x 4-3/16 x 14-1/16 inch)

monitor headphones, 40 ohms; 40 mm drivers with neodymium magnet systems and CCAW voice coils; 1.5 m oxygen- free copper cable. 3.5 mm stereo connector with 1/4" adapter.

OUT OF STOCK

The 360 NandFlasher from Maximus is one of the latest products from the team which allows you to read and write to the NAND firmware chip of the 360, this can be useful in many ways, the first is for people that have consoles that either the drive has totally died and the key for the drive is lost, or that bought damaged consoles that had no drive at all, with the Maximus 360 NandFlasher you will now be able to use the device to read the DVD key right out of the motherboards NAND firmware chip, once you have this key you can then embed it into a new drives firmware and recover the console, we know this is going to be a hugely popular service related tool as there are many people that have consoles like this laying around that they can now recover and sell as refurbished units, where before they were just junk laying in workshops.

If you are a repair centre looking for a cheap yet valuable USB 360 Nand flashing tool to recover dead consoles, or a home user wanting to expand their experience with the 360, the 360 Nand Flasher from Maximus is going to do what you need and be a solid and reliable device. Do note that in its current form to use the 360 NandFlasher soldering is involved, so before you order keep that in mind and make sure you have the right tools and knowledge on how to solder.

Features:

• Professionally manufactured PCB
• Manufactured in the USA
• Includes one installation kit
• Power LED is green for normal operation
• Works will all flash sizes
• SUPER SIMPLE INSTALL !!

 

Line: 6.5V rms max
Headphone: 0.5W into 47 ohm
Distortion: less than 0.01%
Bass: +6/-32dB @40Hz
Middle: +6/-32dB @1.35KHz
Treble: +6/-32dB @15KH
Channel Kill: 80dB at 20Hz-20KHz