PS3 SLIM Replacement Laser KES-450 / KES-450A

IN STOCK

Replace your defective Laser to correct laser problems.

How to find out if your laser needs to be replaced:

• Games/movies take longer than normal to load
• Certain games do not load at all
• Games/movies flicker or jump
• Message: "Disc Read Errors"
• Disc appears damaged or dirty on the screen.

PS3 Model Laser Type Table

IN STOCK

UPDATE: TEAM E3 HAS REPLACED THE ORIGINAL ESATA DOCKING STATION WITH A NEW ESATA HDD ADAPTER WITH SMALLER FORM FACTOR. AS OF 5.20.14 YOU RECEIVE THESE IN SMALLER PACKAGING FROM THE E3 TEAM!

ALL E3 Flashers Kits are sold with European power supply adapters. Power conversion adapters for US/Canada power sold separately.

If you are outside North America, shipping may be slightly more than as shown on our website due to the weight of the E3 Flasher being 3lbs. You will be contacted to pay for additional shipping.

You will also need a downgrade dongle such as the E3 Card Reader AVR to perform the downgrade.

Warning. This product is not 'hard' to install, but is very easy for you to stuff up your console. There is no warranty on the clip device. You have 1 shot to get it onto the console. If you apply the clip wrong you will get a bad read, and the pins on the clip will be damaged.

Please note that you have to make sure the clip is perfectly flush with the motherboard before you press it down.   The majority of the issues lie with improper installation of the clip. If the clip is uneven before you press it down, it will slightly bend the pins on the bottom of the clip.

This Ultimate PS3 Downgrade Device - will allow you to downgrade a NOR PS3 from any new firmare to 3.55!  

This device is only for consoles with NOR flash, not NAND at the moment.  (Doesn't work on Slim 3000 or superslim consoles)

• Click here to check FAT models
• Click here to check Slim models. Please note that newer slim models cannot be downgraded, check this list

Here is a great installation video:

These are the pre-packaged contents for the E3 Flasher complete kit. If you see resellers/distributors selling for less, it's because they are not selling the package with everything seen below.

NOTE: NEW E3 ESATA DOCKING STATION REPLACED BY SMALLER E3 ESATA USB HDD ADAPTER!

This device will require you to simply open up your SLIM PS3 to take the HD out and solder. For the FAT PS3 you WILL require soldering!  As well, the plug that they include with the sata dock is not North American.

Please double check to make sure it works with your PS3 as we will not issue refunds if it is not compatible with your PS3 after it has been installed.

Watch the Official E3DIY Video:

• NOR FLASH ON board
• 3 save MODE
• 1 KEY backup or restore, simplicity is best
• Compatible with all PS3 console - FAT models require soldering
• Integrated interface varieties, perfect extension, will have more functions with future E3 accessories

Team Maximus releases the Stinger 3.0L to RGH your XBox360 PHAT and SLIM (Trinity)

Fast RGH 2 glitcher chip.

New Model 3.0L (with crystal for Corona compatibility) PAD by PAD compatible with last Stinger 2.0, it uses same .jed or .xsvf files, the improvement are:

• Super easy install on Slim Consoles (if used with the new QSB Kit 2.0)
• Ultra fast boot times for SLIM Consoles
• Embedded capacitor for stubborn PHAT consoles

To use the 68nf capacitor for stubborn PHAT consoles just bridge the J68NF jumper and add a Ground wire on the AVG pad to the AV port.

Features:

• Clean and optimized design
• Low digital noise
• Onboard voltage regulations for 1.8v and 1.5v for a stable operation.
• Less solder, 5 points for SLIM, 6 for PHAT
• Less complication for PHAT models having Mode switch instead of having to reprogram for each model
• Ultra fast boot times for PHAT and SLIM in less than 10 secs with or without latest Ameel "long wire trick"
• Comes with programming cable (not a programmer)
• Can be programmed with NandFlasher updated to Nandpro 3.0 or any JTAG programmer available

Contents:

• Maximus Stinger v3.0L
• Ground Cable
• Programming Cable

The SLIM program works on all TRINITY boards.

The PHAT program works on all HDMI models (Falcon, Zephyr, Jasper), and once programmed the model is chosen by setting the onboard solder jumpers.

Chips can be reprogrammed using NANDFLASHER (updated to nandpro 3.0) or any JTAG cable.

Hardware is the same for PHAT and SLIM. It is only the on-board program which can of course be changed later by the end user if needed.

Support:

http://360nandflasher.com

Consoles with physical damage cannot be repaired.

Comes with a 30 day warranty.

This service has a 2-3 business day turnaround, from when we receive the console.

Purchase this service, select your shipping method at checkout and send in your PS2 console. We will repair it, fully test your console, and ship back via the shipping method you have already prepaid!

Send the console only: no Hard drive, cables etc...

Please follow our return policy info to send your machine to us.

http://www.gocybershopping.com/customer/help.php?section=returns