The X3Max is a revolutionary USB development board. The X3Max has a 32bit MCU (processor) and 128KB of memory in which to store user hex, these features are unparalleled and not available in any other USB development board. This powerful hardware specification provides the extensibility required to ensure a future proof solution that will be able to keep up with the latest advances in code development. The X3Max also has an inbuilt MicroSD(HC) slot which provides even further expandability!
With the custom X3Tool programming/flashing software, simple tasks such as uploading hex to the X3 Max are extremely simple as showed in our guide, no drivers are required, simply download the X3Tool software, plug the X3Max in to your computer and flash!
While the X3Max is very simple to use for the end user who just wants to upload pre-made hex to the board, the combination of the powerful X3Max hardware and X3Tool software means that tasks undertaken by developers and advanced users such as editing the payload can be done right from within the X3Tool software! No complicated multi-software solutions are required.
The X3Max comes complete in a sturdy plastic presentation case along with a free screwdriver used to open the casing. THIS DOES NOT WORK ON FIRMWARE 3.42 OR ABOVE UNTIL A NEW EXPLOIT/METHOD IS FOUND!
Tired of your slim PS3 wasting electricity in standby mode? We designed a simple AC cable to allow you to turn the console power off so you dont waste dollars in electricity your not using.
UPDATE: TEAM E3 HAS REPLACED THE ORIGINAL ESATA DOCKING STATION WITH A NEW ESATA HDD ADAPTER WITH SMALLER FORM FACTOR. AS OF 5.20.14 YOU RECEIVE THESE IN SMALLER PACKAGING FROM THE E3 TEAM!
ALL E3 Flashers Kits are sold with European power supply adapters. Power conversion adapters for US/Canada power sold separately.
If you are outside North America, shipping may be slightly more than as shown on our website due to the weight of the E3 Flasher being 3lbs. You will be contacted to pay for additional shipping.
You will also need a downgrade dongle such as the E3 Card Reader AVR to perform the downgrade.
Warning. This product is not 'hard' to install, but is very easy for you to stuff up your console. There is no warranty on the clip device. You have 1 shot to get it onto the console. If you apply the clip wrong you will get a bad read, and the pins on the clip will be damaged.
Please note that you have to make sure the clip is perfectly flush with the motherboard before you press it down. The majority of the issues lie with improper installation of the clip. If the clip is uneven before you press it down, it will slightly bend the pins on the bottom of the clip.
This Ultimate PS3 Downgrade Device - will allow you to downgrade a NOR PS3 from any new firmare to 3.55!
This device is only for consoles with NOR flash, not NAND at the moment. (Doesn't work on Slim 3000 or superslim consoles)
Here is a great installation video:
These are the pre-packaged contents for the E3 Flasher complete kit. If you see resellers/distributors selling for less, it's because they are not selling the package with everything seen below.
NOTE: NEW E3 ESATA DOCKING STATION REPLACED BY SMALLER E3 ESATA USB HDD ADAPTER!
This device will require you to simply open up your SLIM PS3 to take the HD out and solder. For the FAT PS3 you WILL require soldering! As well, the plug that they include with the sata dock is not North American.
Please double check to make sure it works with your PS3 as we will not issue refunds if it is not compatible with your PS3 after it has been installed.
Watch the Official E3DIY Video:
| FLASH FOR YOUR |
The iBlazr LED flash help dramatically improve the quality of photos and video you take with your iPhone, iPad, Android or Windows phone in low-light situations. It easily plugs into the headphone port of the device and has its own battery, so it doesn't drain the power of your smartphone—yet has enough power to take up to 500 photos before needing a recharge.
GENTLE LIGHT FOR YOUR SELFIES
Download the app here!
VIDEO LIGHT FOR
KEY VIDEO FEATURES
|In the Box|
LIGHT AND DIMENSIONS
Height: 27 mm (1 inch)
Built-in rechargeable lithium-ion battery
Constant light mode:
Sleep Mode – Up to three month
Cold Shoe Mount
Power Output:Off-smartphone Constant Light Modes:
Flash mode – up to 270 Lux at 1 m
Thermo sensor (preventing from overheat)
Battery controller (check the battery level by pushing
Light Controller (measuring ambient light)
Flexible ChargerPerfect for:
Length – 42cm (16.5 inches)
Warning: DO NOT insert the earphones or any other 3.5 mm connector into the Flexible iblazr Charger!
For more information about the iBlazr visit the official website at http://iblazr.com/int/faq