Improve the performance and ease of install for your CoolRunner and NAND-X to a Phat motherboard with this easy to install QSB (Quick Solder Board).
Use your Xecuter CK3 Pro or CK3i to update your NAND-X firmware to the latest version NANDPRO so you can use your NAND-X to program your Xecuter CoolRunner over USB.
Note: The CK3 Pro (Rev D) requires a 1 wire modification (Older CK3 Pro and CK3i do not require this. Not compatible with CK3 Lite)
The Xecuter NAND-X Wire Install Kit is a spare part kit for the Xecuter NAND-X / JTAG USB Programmer. This Kit includes the color coded wires for direct NAND-X installs.
Info: If you order the Xecuter NAND-X / JTAG USB Programmer then you have one Xecuter NAND-X Wire Install Kit included. But if you have more Xbox 360 motherboards to flash or to repair then you need this spare part
This is a custom made LPT JTAG Cable that is designed direct from the official Xilinx schematics (not the cheap design that is going around - this is the higher spec design from Xilinx)
Fully compatible with iMPACT software and tested 100% with various Xilinx products that have a JTAG port including the Xecuter CoolRunner.
Comes complete with an Xecuter CK3 custom power cable for the Xecuter CoolRunner while updating over LPT.
The highest quality reset glitch mod at the lowest price - accept no imitations !
World famous XBOX hardware developers Team Xecuter are happy to introduce the Xecuter CoolRunner - The Ultimate Reset Glitch Mod !
In early September 2011, Xbox scene homebrew gurus Tiros and GliGli announced that there was finally a way to boot unsigned (homebrew) code on Xbox Phat & Slim models regardless of which kernel was installed ! (before now JTAG'ing a console for homebrew was limited to very old versions of console/kernel and thus made them very difficult and expensive to buy)
Naturally a whole range of third party devices have come onto the market which were basically copies of the DIY design that was released by Tiros and GliGli. As usual the whole scene looked to Team Xecuter to see what design they could come up with to make this the most rock solid mod possible and they have done it again with the Xecuter CoolRunner !
The possibilities for homebrew on the Xbox 360 are endless. There have been hundreds of extra features since JTAG'ing became possible. Pme of the first things you can do with this is recover your DVD key from your console if it was ever lost in the paste. There are thousands of consoles out there that are gathering dust beciase of this - and this will solve all of those problems :)
This device is designed primarily to aid or assist in the repair or replacement of defective hardware and also for the use of and development of legal open source software. It does not enable any kind of piracy or have any code whatsoever that circumvents any kind of protection. It is shipped blank and you have to program it with the correct code that matches your motherboard version. We do not support nor encourage, if possible, potential infringements of others intellectual property rights - please do not contact us with any question related to this use as we will not respond. DO NOT use or buy this product if you are looking to perform any illegal activity.
OUT OF STOCK AS OF APRIL 10 - ETA END OF APRIL*
*DATE SUBJECT TO CHANGE WITHOUT NOTICE
ALL E3 Flashers Kits are sold with European power supply adapters. Power conversion adapters for US/Canada power sold separately.
If you are outside North America, shipping may be slightly more than as shown on our website due to the weight of the E3 Flasher being 3lbs. You will be contacted to pay for additional shipping.
You will also need a downgrade dongle such as the E3 Card Reader AVR to perform the downgrade.
Warning. This product is not 'hard' to install, but is very easy for you to stuff up your console. There is no warranty on the clip device. You have 1 shot to get it onto the console. If you apply the clip wrong you will get a bad read, and the pins on the clip will be damaged.
Please note that you have to make sure the clip is perfectly flush with the motherboard before you press it down. The majority of the issues lie with improper installation of the clip. If the clip is uneven before you press it down, it will slightly bend the pins on the bottom of the clip.
This Ultimate PS3 Downgrade Device - will allow you to downgrade a NOR PS3 from 4.55 to 3.55! You have to make sure the PS3 originally came with 3.55 firmware or lower from factory.
This device is only for consoles with NOR flash, not NAND at the moment
Here is a great installation video:
These are the pre-packaged contents for the E3 Flasher complete kit. If you see resellers/distributors selling for less, it's because they are not selling the package with everything seen below.
This device will require you to simply open up your SLIM PS3 to take the HD out and solder. For the FAT PS3 you WILL require soldering! As well, the plug that they include with the sata dock is not North American.
Please double check to make sure it works with your PS3 as we will not issue refunds if it is not compatible with your PS3 after it has been installed.
Watch the Official E3DIY Video: