Those that have fitted a CoolRunner to an Xbox Slim will be no stranger to the fact that it can take a great deal of trial and error to get the optimized boot times down to less than 5 seconds. The main issue is the CPU_RST wire which has to be up to 50cm long and then coiled underneath the motherboard. In many cases the positioning of the coil is a factor due to signal interference. Then you have to try different lengths, 40cm, Xecuter has developed a simple yet elegant solution for this problem. Using the process of serpentining, Xecuter has designed a QSB PCB for the Xbox 360 slim that fits neatly into place, giving you an optimized solution enabling you to select several different lengths without having to cut any wires and eliminates any guess work and possible signal interference issues. Simply cut the blue CPU_RST wire to 8cm and then you can select from 50cm, 47cm, 41cm, 38cn, 35cm, 32cm & 29cm.
Never solder/unsolder the trace cut again!
When using a Sputnik Probe you have to repair the trace when you have finished programming, and if you ever need to flash the drive again you would have to de-solder.
This simple PCB add-on enables you to solder the board once and then thats all you will ever need to do. The simple switch will open / close the circuit and there is an extra large pad to use when probing for when you need to unlock the SPI.
Open / Close trace cut without further soldering
Large pad for easy probing
Easy to install - takes minutes!
NOTE: This is NOT the SPUTNIK360 - Liteon DG-16D4S DVD Unlock Switch, this is an addon product for the SPUTNIK360 PROBE and will not unlock the SPI without the use of the Probe.
This device is designed primarily to aid or assist in the repair or replacement of defective hardware. It does not enable any kind of piracy or have any code or any kind of microchip whatsoever that circumvents any kind of protection. It is a basic circuit of wires and diodes that is all. We do not support nor encourage, if possible, potential infringements of others intellectual property rights - please do not contact us with any question related to this use as we will not respond. DO NOT use or buy this product if you are looking to perform any illegal activity.
This charging station offers a home to dock and charge your Xbox 360 controller and also a separate battery charger slot. Extend your game play and power up those endless nights of nonstop gaming. The charging dock is equipped with smart battery indicators to show battery status. The Led status lights let you know when each battery is partially or fully charged. No separate power supply required, easily connects to your Xbox 360 USB port.
Team Maximus releases the Stinger 3.0L to RGH your XBox360 PHAT and SLIM (Trinity)
Fast RGH 2 glitcher chip.
New Model 3.0L (with crystal for Corona compatibility) PAD by PAD compatible with last Stinger 2.0, it uses same .jed or .xsvf files, the improvement are:
To use the 68nf capacitor for stubborn PHAT consoles just bridge the J68NF jumper and add a Ground wire on the AVG pad to the AV port.
The SLIM program works on all TRINITY boards.
The PHAT program works on all HDMI models (Falcon, Zephyr, Jasper), and once programmed the model is chosen by setting the onboard solder jumpers.
Chips can be reprogrammed using NANDFLASHER (updated to nandpro 3.0) or any JTAG cable.
Hardware is the same for PHAT and SLIM. It is only the on-board program which can of course be changed later by the end user if needed.
The PIC18F4550 USB Dev Kit is loaded with features, including a large 32kb of program memory, optimized for C programs. The PIC18F4550 Development Board comes complete with the Microchip PIC18F4550 microcontroller pre-installed, together with the necessary crystal and power supply components, for a ready-to-run solution. Simply connect the power and download your program, using the easy to use programming interface and software, and your ready to start exploring the new PIC18 USB.
PIC18F USB Dev Kit Programs can be downloaded or updated directly to the microcontroller using the USB in-circuit programming interface together with a suitable programmer or MPLabs HID Bootloader software.
Now works with v3 Heremes!
Pushbuttons and LED's are also included on our development board for testing and developing your code. This board is the ideal for applications requiring a USB Connection together with a large number of A/D inputs for monitoring and control.
Our new PIC18F4550 Development board will get you started with an inexpensive, ready-to-run solution, which is ideal for the student or hobbyist.