NEW V2.0 Version with Full POST Monitoring and CR3 Pro Rater Support. Also includes speed enhancements (2-3 minutes faster than JRP v1 !)
The new TX J-R Programmer V2 has been created to cater to the budget conscious and coded to work hand in hand with the latest version of the J-Runner app.
A third of the size of the TX NAND-X and optimized to run faster than any other USB-SPI based tool (Example Speeds: Others average 16M read 7m 20s, JRP v2 average 16M read 3mins), this nifty tool can fully read/write NAND over SPI, program CoolRunners or any Xilinx based RGH device over USB and also able to program onboard sounds using the TX SONUS 360 !
Complete with a CR JTAG cable so you simply plug 'n program without any soldering using the latest J-Runner App (needs to be at least Build 283). Also comes with NAND installation wires that have the connectors that are compatible with the NAND-X QSB boards. If you don't use the QSB's you can simply cut off the connectors and do a normal wires only install.
The J-R Programmer V2 is also fully upgradeable and can be programmed using the Xecuter X360USB PRO Update app. Onboard LED's indicate Power and BootLoader mode.
RED LED: Bootloader Mode (Switch to the left)
GREEN LED: J-R Programmer Mode (Switch to the right)
RED LED FLASHING: R/W Activity & POST Activity (Switch to the right)
Those of you looking for a similar setup as the TX NAND-X RGH Edition V3, we recommend the following items that are available for purchase separately:
NOTE: This device is designed primarily to aid or assist in the repair or replacement of defective hardware. It does not enable any kind of piracy or have any code or any kind of microchip whatsoever that circumvents any kind of protection. It is a basic circuit of wires and diodes that is all. We do not support nor encourage, if possible, potential infringements of others intellectual property rights - please do not contact us with any question related to this use as we will not respond. DO NOT use or buy this product if you are looking to perform any illegal activity
Allen & Heath Zone 62 Club Mixer Technical Specifications 0dBu = 0.775 Volts rms +4dBu = 1.23V rms 0dBV = 1 Volt rms -10dBV = 316mV rms Maximum output level XLR +26dBu into >2k ohm load TRS jack +21dBu into >2k ohm load RCA Phono +15dBu into >10K ohm load Internal headroom Channels +21dB Mix to output +23dB Peak indicators Turn on 5dB before clipping Meters MIX /MONITOR Peak hold 12 LED 3 colour STEREO CHANNEL Peak reading 4 LED 3 colour Frequency response 20Hz to 40kHz +0/-1dB Distortion THD+noise measured at +14dBu 1kHz < 0.006% Crosstalk channel shutoff measured at 1kHz < 90dB Noise measured rms 22Hz to 22kHz MIC EIN -128dB referred to 150 ohm source Residual output noise XLR -90dBu (-94dB S/N) TRS jack -84dBu (-84dB S/N) L RCA -92dBu (-84dB S/N) Mix noise, ch routed XLR -86dBu (-90dB S/N) TRS jack -82dBu (-82dB S/N) RCA Phono -91dBu (-83dB S/N) Power Supply Internal switch mode power unit with auto sensing mains input. MAINS IN socket IEC 3 pin Power lead Country dependent with moulded mains plug supplied AC mains 100 to 240V AC @ 50/60Hz Consumption 30W max Mains fuse rating 100-240V AC T500mA 20mm