NEW V2.0 Version with Full POST Monitoring and CR3 Pro Rater Support. Also includes speed enhancements (2-3 minutes faster than JRP v1 !)
The new TX J-R Programmer V2 has been created to cater to the budget conscious and coded to work hand in hand with the latest version of the J-Runner app.
A third of the size of the TX NAND-X and optimized to run faster than any other USB-SPI based tool (Example Speeds: Others average 16M read 7m 20s, JRP v2 average 16M read 3mins), this nifty tool can fully read/write NAND over SPI, program CoolRunners or any Xilinx based RGH device over USB and also able to program onboard sounds using the TX SONUS 360 !
Complete with a CR JTAG cable so you simply plug 'n program without any soldering using the latest J-Runner App (needs to be at least Build 283). Also comes with NAND installation wires that have the connectors that are compatible with the NAND-X QSB boards. If you don't use the QSB's you can simply cut off the connectors and do a normal wires only install.
The J-R Programmer V2 is also fully upgradeable and can be programmed using the Xecuter X360USB PRO Update app. Onboard LED's indicate Power and BootLoader mode.
RED LED: Bootloader Mode (Switch to the left)
GREEN LED: J-R Programmer Mode (Switch to the right)
RED LED FLASHING: R/W Activity & POST Activity (Switch to the right)
Those of you looking for a similar setup as the TX NAND-X RGH Edition V3, we recommend the following items that are available for purchase separately:
NOTE: This device is designed primarily to aid or assist in the repair or replacement of defective hardware. It does not enable any kind of piracy or have any code or any kind of microchip whatsoever that circumvents any kind of protection. It is a basic circuit of wires and diodes that is all. We do not support nor encourage, if possible, potential infringements of others intellectual property rights - please do not contact us with any question related to this use as we will not respond. DO NOT use or buy this product if you are looking to perform any illegal activity
You may be the greatest living banana-pianist, but how will you ever know if you don’t make yourself a banana piano? Good news, that project and countless others are easier than you think they are with MaKey MaKey.
Using the MaKey MaKey you can make anything into a key (get it?) just by connecting a few alligator clips. The MaKey MaKey is an invention kit that tricks your computer into thinking that almost anything is a keyboard. This allows you to hook up all kinds of fun things as an input. For example, play Mario with a Play-Doh keyboard, or piano with fruit!
The MaKey MaKey uses high resistance switching to detect when you’ve made a connection even through materials that aren’t very conductive (like leaves, pasta or people). This technique attracts noise on the input, so a moving window averager is used to lowpass the noise. The on-board ATMega32u4 communicates with your computer using the Human Interface Device (HID) protocol which means that it can act like a keyboard or mouse.
There are six inputs on the front of the board, which can be attached to via alligator clipping, soldering to the pads, or any other method you can think of. There are another 12 inputs on the back, 6 for keyboard keys, and 6 for mouse motion, which you can access with jumpers via the female headers. If you wish to use a different set of keys, or otherwise change the behavior of your MaKey MaKey, you can simply reprogram it using the Arduino environment. Oh yeah, we didn’t mention that the MaKey MaKey is an Arduino-compatible controller? That’s right, it runs the Leonardo bootloader so reprogramming is fast and easy.
Note: Now included with the MaKey MaKey is a USB cable, pack of jumper wires as well as a pack of alligator clips!
Note: See the GitHub link below for support with the Arduino IDE.
Multi-function Anti-spy Detector K18 Camera GSM Audio Bug Finder GPS Signal Lens RF Tracker