NEW V2.0 Version with Full POST Monitoring and CR3 Pro Rater Support. Also includes speed enhancements (2-3 minutes faster than JRP v1 !)
The new TX J-R Programmer V2 has been created to cater to the budget conscious and coded to work hand in hand with the latest version of the J-Runner app.
A third of the size of the TX NAND-X and optimized to run faster than any other USB-SPI based tool (Example Speeds: Others average 16M read 7m 20s, JRP v2 average 16M read 3mins), this nifty tool can fully read/write NAND over SPI, program CoolRunners or any Xilinx based RGH device over USB and also able to program onboard sounds using the TX SONUS 360 !
Complete with a CR JTAG cable so you simply plug 'n program without any soldering using the latest J-Runner App (needs to be at least Build 283). Also comes with NAND installation wires that have the connectors that are compatible with the NAND-X QSB boards. If you don't use the QSB's you can simply cut off the connectors and do a normal wires only install.
The J-R Programmer V2 is also fully upgradeable and can be programmed using the Xecuter X360USB PRO Update app. Onboard LED's indicate Power and BootLoader mode.
RED LED: Bootloader Mode (Switch to the left)
GREEN LED: J-R Programmer Mode (Switch to the right)
RED LED FLASHING: R/W Activity & POST Activity (Switch to the right)
Those of you looking for a similar setup as the TX NAND-X RGH Edition V3, we recommend the following items that are available for purchase separately:
NOTE: This device is designed primarily to aid or assist in the repair or replacement of defective hardware. It does not enable any kind of piracy or have any code or any kind of microchip whatsoever that circumvents any kind of protection. It is a basic circuit of wires and diodes that is all. We do not support nor encourage, if possible, potential infringements of others intellectual property rights - please do not contact us with any question related to this use as we will not respond. DO NOT use or buy this product if you are looking to perform any illegal activity
UPDATE: TEAM E3 HAS REPLACED THE ORIGINAL ESATA DOCKING STATION WITH A NEW ESATA HDD ADAPTER WITH SMALLER FORM FACTOR. AS OF 5.20.14 YOU RECEIVE THESE IN SMALLER PACKAGING FROM THE E3 TEAM!
ALL E3 Flashers Kits are sold with European power supply adapters. Power conversion adapters for US/Canada power sold separately.
If you are outside North America, shipping may be slightly more than as shown on our website due to the weight of the E3 Flasher being 3lbs. You will be contacted to pay for additional shipping.
You will also need a downgrade dongle such as the E3 Card Reader AVR to perform the downgrade.
Warning. This product is not 'hard' to install, but is very easy for you to stuff up your console. There is no warranty on the clip device. You have 1 shot to get it onto the console. If you apply the clip wrong you will get a bad read, and the pins on the clip will be damaged.
Please note that you have to make sure the clip is perfectly flush with the motherboard before you press it down. The majority of the issues lie with improper installation of the clip. If the clip is uneven before you press it down, it will slightly bend the pins on the bottom of the clip.
This Ultimate PS3 Downgrade Device - will allow you to downgrade a NOR PS3 from any new firmare to 3.55!
This device is only for consoles with NOR flash, not NAND at the moment. (Doesn't work on Slim 3000 or superslim consoles)
Here is a great installation video:
These are the pre-packaged contents for the E3 Flasher complete kit. If you see resellers/distributors selling for less, it's because they are not selling the package with everything seen below.
NOTE: NEW E3 ESATA DOCKING STATION REPLACED BY SMALLER E3 ESATA USB HDD ADAPTER!
This device will require you to simply open up your SLIM PS3 to take the HD out and solder. For the FAT PS3 you WILL require soldering! As well, the plug that they include with the sata dock is not North American.
Please double check to make sure it works with your PS3 as we will not issue refunds if it is not compatible with your PS3 after it has been installed.
Watch the Official E3DIY Video:
* DATE SUBJECT TO CHANGE WITHOUT NOTICE
Original DVD drive PCB for Liteon Slim drives on Xbox 360 slim. These are unlocked and are ready to go!
Just retrieve original keys from old slim drive, 9504, 0225, 0401 and install this new board
and flash with the keys!
We used the Kamikaze method to unlock these boards!
NO other details available for this product.