1 X UNO Board
1 X USB Cable
1 X Jump Cable
1 X Breadboard
5 X LED Light
1 Pack Resistor
1 X Female to male dupond line
1 X Potentiometer
1 X Buzzer
1 X 74HC595
1 X Infrared receiver
1 X LM35
1 X Flame Sensor
1 X Ball Switch
1 X Photoresistor
1 X Key button
1 X Remote control
1 X 4-digit display tube
1 X 8*8 Dot matrix module
1 X 1-digit display tube
1 X Stepper motor driver board
1 X Stepper motor
1 X 9g Servo
1 X IIC 1602 LCD
1 X XY joystick module
1 X Temperature module
1 X Water test module
1 X RFID Module
1 X RFID keychain
1 X RFID White card
1 X Sound Module
1 X Relay Module
1 X Clock Module
1 X 4*4 Key board
1 X RGB 3 color module
1 X 9V battery Snap
Presenting Minimus, a high quality production grade AVR USB Development Unit that is clean in design, low in cost and readily available to resellers around the globe. There are hundreds of projects available for the AVR USB hobbyist looking for a powerful yet cost effective solution. Works with Open Source LUFA USB firmware library and Open Source LibUSB software library.
22 Programmable I/O Lines
512 Byte SRAM
512 byte EEPROM
16 MIPS Throughput
USB 2.0 High Speed
16MHz Quartz Crystal Oscillator Circuit
5V USB Powered
Power / Status LED's
Male USB Connector - No Cable Required
Access to all IO's
Easy Program / Update with Atmel FLIP (Flexible In-system Programmer)
Robust HW/Reset Buttons (Simple Once-Only Operation When Programming)
Full LUFA Compatability
Full LibUSB Compatability
Simple Plug n Play
Atmel FLIP Software Drivers: http://www.atmel.com/dyn/products/to...p?tool_id=3886
Software Compatible With Windows 9x / Me / NT / 2000 / XP / Vista / 7 and Linux.
Here are some development resources for AVR USB Development:
AVR-USB-162 blink LED demo code (C source and HEX)
AVR-USB-162 button demo code (C source and HEX)
AVR-USB-162 frequency generator (C code and HEX)
AVR-USB-162 mouse demo code C source
AVR-USB-162 virtual COM port demo code C source
MyUSB LGPL USB stack from Dean Camera
The Minimus AVR USB is powered by an Atmel AT90USB162 that is pre-programmed with the bootloader which allows code to be programmed inside the chip without any external programmer, just download the FLIP software from Atmel's web site and load your HEX code. To enter the bootloader mode you should simply press and hold HWB button, then press and release the RST button.
The PIC18F4550 USB Dev Kit is loaded with features, including a large 32kb of program memory, optimized for C programs. The PIC18F4550 Development Board comes complete with the Microchip PIC18F4550 microcontroller pre-installed, together with the necessary crystal and power supply components, for a ready-to-run solution. Simply connect the power and download your program, using the easy to use programming interface and software, and your ready to start exploring the new PIC18 USB.
PIC18F USB Dev Kit Programs can be downloaded or updated directly to the microcontroller using the USB in-circuit programming interface together with a suitable programmer or MPLabs HID Bootloader software.
Now works with v3 Heremes!
Pushbuttons and LED's are also included on our development board for testing and developing your code. This board is the ideal for applications requiring a USB Connection together with a large number of A/D inputs for monitoring and control.
Our new PIC18F4550 Development board will get you started with an inexpensive, ready-to-run solution, which is ideal for the student or hobbyist.
Tired of your slim PS3 wasting electricity in standby mode? We designed a simple AC cable to allow you to turn the console power off so you dont waste dollars in electricity your not using.
Get The Edge With Comfort And Control.
Consoles with physical damage cannot be repaired.
Comes with a 30 day warranty.
This service has a 2-3 business day turnaround, from when we receive the console.
Purchase this service, select your shipping method at checkout and send in your PS2 console. We will repair it, fully test your console, and ship back via the shipping method you have already prepaid!
Send the console only: no Hard drive, cables etc...
Please follow our return policy info to send your machine to us.