Allen & Heath Zone 62 Club Mixer Technical Specifications 0dBu = 0.775 Volts rms +4dBu = 1.23V rms 0dBV = 1 Volt rms -10dBV = 316mV rms Maximum output level XLR +26dBu into >2k ohm load TRS jack +21dBu into >2k ohm load RCA Phono +15dBu into >10K ohm load Internal headroom Channels +21dB Mix to output +23dB Peak indicators Turn on 5dB before clipping Meters MIX /MONITOR Peak hold 12 LED 3 colour STEREO CHANNEL Peak reading 4 LED 3 colour Frequency response 20Hz to 40kHz +0/-1dB Distortion THD+noise measured at +14dBu 1kHz < 0.006% Crosstalk channel shutoff measured at 1kHz < 90dB Noise measured rms 22Hz to 22kHz MIC EIN -128dB referred to 150 ohm source Residual output noise XLR -90dBu (-94dB S/N) TRS jack -84dBu (-84dB S/N) L RCA -92dBu (-84dB S/N) Mix noise, ch routed XLR -86dBu (-90dB S/N) TRS jack -82dBu (-82dB S/N) RCA Phono -91dBu (-83dB S/N) Power Supply Internal switch mode power unit with auto sensing mains input. MAINS IN socket IEC 3 pin Power lead Country dependent with moulded mains plug supplied AC mains 100 to 240V AC @ 50/60Hz Consumption 30W max Mains fuse rating 100-240V AC T500mA 20mm
4 ohms: 150 watts RMS per channel 8 ohms: 90 watts RMS per channel 8 ohms: 300 watts RMS, bridged mode >105dB 10Hz - 70kHz +0, -3dB < 0.02% @ 4ohms, 20Hz - 20kHz +4dB for rated output -85dB, 1kHz +/- 50 mV, Servo controlled
Don’t limit your projects, think big, think MEGA! The Arduino Mega 2560 has been designed with bigger and more ambitious projects in mind. The large number of analog and digital pins, together with a larger memory makes it ideal for devices like 3D printers and other demanding applications. Backward compatibility with existing shields and sketches is provided, but other shields target the Mega specifically, exploiting the full potential of this board.
The Mega 2560 is a board based on the 8-bit AVR microcontroller ATmega2560 by Atmel. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports). It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable. The Mega 2560 board is compatible with most shields designed for the Uno. To compare this board to the current, past or outdated boards see the Comparison Page.
|Input Voltage (recommended)||7-12V|
|Input Voltage (limit)||6-20V|
|Digital I/O Pins||54|
|PWM Digital I/O Pins||14|
|Analog Input Pins||16|
|DC Current per I/O Pin||40 mA|
|DC Current for 3.3V Pin||50 mA|
|Flash Memory||256 KB|
|Flash Memory for Bootloader||8 KB|
|Clock Speed||16 MHz|
Arduino MEGA 2560 is open-source hardware! These are the relevant files:
If you want more information about programming the Arduino Mega 2560 or how to interface hardware with it, please go to the Product Page.
Arduino Mega 2560 is programmed, as all the other Arduino boards with the Arduino Software (IDE) that you can download for free.
Arduino Uno Rev3 is programmed, as all the other Arduino boards with the Arduino Software (IDE) that you can download for free.