These are a replacement LITEON DG-16D2S DVD drive for the Xbox 360, they are hard to get a hold of brand new as many sold online are refurbished from the factory.
If you’re repairing for Xbox 360 consoles and need a solid for Xbox 360 replacement DVD drive, the LITEON DG-16D2S is the best option out there to date.
Note about swapping XBox 360 DVD Drives:
With all Xbox 360 DVD drives you need to extract the DVD key from your old drive's BIOS and flash that key into the drive you are replacing it with. You may also need to spoof the drive if you're not replacing a drive with the exact same brand or model. This is not a simple swap-out procedure and should only be performed by a competent technician.
NO RETURNS FOR BUYING ERRORS FOR THIS ITEM.
This is the new 4 position resistor - 4th value details will be added shortly.
This is the new Xecuter LT Switch v1.6 - the latest version in the #1 selling Xecuter LT Switch range.
Xecuter has designed a simple switch for all the Liteon drives that enables firmware full read/write. They have also included an ON/OFF Led to show correct operation when switching to 0x72 vendor mode.
Now Includes MULTI-R Function. After the discovery that a small number of Liteon drives would not dump the fw with a 20 ohm resistor - but required an 18 Ohm or 22 Ohm resistor - so you can now select between 18, 20 and 22 Ohms ! (Default should be set to 20 Ohms - this will work 99% of the time)
The installation is very simple and takes about 5 minutes if you have some small experience with a soldering iron. It has been tested with the latest Jungle Flasher 0.1.73. All Liteon drive versions have been tested with 100% Success (Including the troublesome Winbond IC). There is no need to remove the LT Switch after it has been installed - simply switch to normal mode and you are good to go. Even if you have to upgrade in the future - you don't have to touch the switch again !
Don't be fooled by more expensive copycat products. This is the only solution you need to do a very simple job. Remember this product follows the K.I.S.S engineering principle (KEEP IT SIMPLE STUPID) :)
The Only Liteon Solution Recommended By Team Jungle !
Enables Read/Write on ALL Liteon 74850, 83850, 93450 DVD Drives
Easy & Simple Install - Install Once & Forget
Enable / Disable Switch
Multi-R Switch (18, 20, 22 Ohms)
No Need To Uninstall
Works with ALL tools including the latest Jungle Flasher
This device is designed primarily to aid or assist in the repair or replacement of defective hardware and also for the use of and development of legal open source software. It does not enable any kind of piracy or have any code whatsoever that circumvents any kind of protection. We do not support nor encourage, if possible, potential infringements of others intellectual property rights - please do not contact us with any question related to this use as we will not respond. DO NOT use or buy this product if you are looking to perform any illegal activity.
The American DJ Crank-2 System is the ultimate mobile stand system making life on the road even easier! Before the Crank-2 system you would have to push-up your heavy lights by hand, but now you can set up your lights at arms reach then easily ?crank up? the Crank-2 system up to10 feet without having to struggle!
The 360 LiteKey by Maximus is an advanced version of the Lite-On rebuild board, this little device serves as not only a rebuild PCB for the Lite-On 83850 V2 & 93450 V3, but it also acts as a Vampire spear as well, so all you need to do with the 360 LiteKey is install it and use the Xtractor Pro, or the 360 power unit from the USB Xtractor to then do a full firmware dump of your drive.
But that’s not the only function of this neat little invention, as some of you may know, when using the LT firmware on the Lite-On 83850 V2 & 93450 V3 drives, before you accept any updates for the 360 console you should really flash the firmware on your drive back to its original state before doing the update, this is where the Maximus 360 LiteKey really shines, because after installation there is no need to open the drive again to be able to do this, the 360 LiteKey can auto switch between operational mode or firmware extraction mode, where if you were using something like the standard Lite-On rebuild board, to flash the drive back to its original state you would need to open the drive and use the Vampire to make the full dump needed to finalize the process, with Maximus 360 LiteKey that’s a thing of the past, after the first install there is no need to ever open the drive again.